foofoofoofoofoofoofoofoofoofoofoofoofoofoofoofoofoofoofoofoofoofoofoofoofoofooairporthospitalsindustrylogisticsretailArtboardempowermentinnovationbrochureproductpassionproductsrespectteamworkArtboard@2xwhitepaperwiring-diagramsfacebookinstagramlinkedintwitteryoutubearrowarrow-redux-bigarrow-redux-toparrow-redux-toparrow-reduxarrowArtboard@2xcountrydownloadeyefile2filtergridhamburgerlanguagelistnopdfphoneplusresetsearchsubscribevideoyesArtboard@2x

IXIO-DT1

ACTIVATION AND SAFETY SENSOR FOR AUTOMATIC SLIDING DOORS
ixio-dt1_st

Description

BEA’s IXIO-DT1 is the premier motion and presence sensor, combining the highest quality and the best value for the automatic sliding door industry.

This dual technology product is a highly flexible and user-friendly solution for sliding doors, industrial doors, vehicle gate detection and off-door automation.

The IXIO-DT1 can be adjusted into an ANSI compliant solution and has earned a comprehensive list of credentials and certifications, including FCC and IP54.

The IXIO-DT1 ensures convenience, safety and energy efficiency for all BEA customers and end users.

Features

Energy efficient

Ten microwave activation sensitivity settings and three infrared safety immunity settings; Ability to distinguish between approaching and departing traffic

Precise presence detection

Two 24-spot high-density, infrared safety curtains providing precise presence detection

Standards compliant

Fully monitored internally, capable of external monitoring

Easily adjustable

Four visible red alignment spots are projected on the ground to assist in precise IR curtain adjustment

Table of specifications

Technology

Microwave Doppler Radar

Active Infrared

Detection Mode

Motion

Presence

Transmitter Frequency

24.150 GHz

N/A

Transmitter Radiated Power

< 20 dBm EIRP

N/A

Transmitter Power Density

< 5 mW / cm2

N/A

Spot Size

N/A

2 in × 2 in

Max. Number of Spots

N/A

24 per curtain

Max. Number of Curtains

N/A

2

Output

Maximum Contact Voltage
Maximum Contact Current
Hold Time

Electro-mechanical-relay (potential and polarity free)
30 VDC
1 A
0.5 – 9 s

Solid-state-relay (potential and polarity free)
42 VDC
400 mA
0.3 – 1 s

Test Input

N/A

Sensitivity: Low: < 1 V; High: > 10 V (max. 30 V)
Response time on test request: typical: < 5 ms

Supply Voltage

12 – 24 VAC ±10%; 12 – 30 VDC ±10% (to be operated from SELV compatible power supplies only)

 

Power Consumption

< 2.5 W

 

Mounting Height

78 in – 138 in (6.5 ft – 11.5 ft)

 

Temperature Range

−13 °F to 131 °F
0 – 95% relative humidity, non-condensing

 

Degree of Protection

IP54

 

Applicable Directives

R&TTE 1999 / 5 / EC; EMC 2004 / 108 / EC; MD 2006 / 42 / EC;
RoHS 2002 / 95 / EC

 

Dimensions

10.6 in (W) × 2.25 in (H) × 2.27 in (D)

 

Cable Length

120 in (10 ft)

 
Versions
  • ixio-dt1_st
    10IXIODT1

    Activation and safety sensor for automatic sliding doors

Accessories
Videos
Downloads
Frequently asked questions

Why will the IXIO’s active infrared safety pattern not hold the door open?

The brown and blue wires must be connected, or F1 must be set to “1” using the remote control.

 

Why is the PNP harness not working on a BESAM control?

The harness is reversed; the short harness plugs into the IXIO.

 

Why is the RECORD sliding door holding open? 

The RECORD control uses a normally closed safety circuit; set the safety output to N.C.

 

Why is the IXIO bliking red on a DORMA door?

The IXIO is defaulted to monitoring ON; connect the two (2) purple monitoring wires to the control.

 

How do I eliminate four (4) orange LED flashes or “low AIR”?

Verify the pattern width shutters are not closed (the software should still be set to wide).Verify the active infrared safety pattern is not tilted out too far away from the door.

Turn off the 2nd active infrared safety pattern row.

 

Why does the door recycle open?

If the red LED illuminates, the active infrared safety curtain needs adjusted.  

If the green LED illuminates, the microwave activation angle/sensitivity/immunity needs adjusted.

 

What are the extra wires not connected to the door control?

The two (2) purple wires are for monitoring and the yellow wire is for N.C. activation relay.

 

How do I locate the IXIO’s active infrared safety pattern relative to the door face?

Double-click the gray knob to turn on the visible red aligment spots or press UNLOCK > MAGIC WAND > + on the remote control, and then use the red knob to adjust active infrared saftey pattern to within 3” of the face of the sliding door panel.  After adjustment, relaunch a setup.

 

How do I use an IXIO for 1-way traffic reactivation?

If the door is equipped with a two-way traffic option, connect the white and green wires to the activation circuit.

If the door is NOT equipped with a two-way traffic option, DO NOT connect the white and green wires to the activation circuit; instead, connect the brown and blue wires to the safety circuit.

Using the LCD, set RAD: REENTRY to value “”3″” or “”4″”. Walk-test to ensure there is a minimum of a 24” reactivation zone.

 

Why does the IXIO LED blink fast red when I try to unlock it with the remote control?

A lock code has been entered.  To remove it, power cycle the IXIO and then press UNLOCK > LOCK > 0000.

 

See all our products